Xerox Fault Codes

Table of Contents

Below is the list of Xerox printer fault codes. For some reason some Xerox printers come without the list of fault codes in the manual while some others do.

Code Description
002-770 The job template could not be processed due to insufficient hard disk space.
Delete unnecessary data from the hard disk.
003-750 No document was saved for the double-sided Booklet Creation feature. Check
the setting of the double-sided Booklet Creation feature.
003-751 The specified document area is too small. Select a higher resolution or a larger
scan area.
003-754
003-755
An error occurred in the document scanner. Reset the document, and scan
again.
003-756 The fax document is completely white. Check that the original is not white, or
that the front and back sides have been reversed.
003-760 Incompatible features are selected in the document scan conditions. Check the
selected options.
003-761 The paper size in the tray selected by auto tray switching, differs from the paper
size in the tray selected at the tray selection. Either change the paper size for
the tray, or change the paper type priority setting.
003-763 An error occurred when reading the Gradation Adjustment Chart. Place the
chart properly on the document glass.
003-780 Compression of scanned data was unsuccessful. Lower the resolution or
reduction/enlargement ratio to reduce the data size, or send the document in
smaller segments.
003-795 The reduction/enlargement ratio exceeds the setting range when the scanned
document is enlarged/reduced to the specified paper size. Directly enter the
reduction/enlargement ratio, or change the paper size.
003-981 Stapling mixed size documents is available only for documents with the same
width. Cancel the staple feature or reset the documents with the same width.
005-210
005-275
005-280
005-283
005-284
005-285
005-286
An error occurred in the document feeder. Contact the Xerox Welcome Center.
012-211
012-212
012-221
012-223
012-224
The finisher malfunctioned. Turn the power off and on. Contact the Xerox
Welcome Center if the problem persists.
012-259
012-260
012-263
012-280
012-282
012-283
012-284
012-285
012-291012-293
012-294
012-295
012-296
The finisher malfunctioned. Turn the power off and on. Contact the Xerox
Welcome Center if the problem persists.
016-210 An error occurred on the software option settings. Turn the power off and on.
Contact the Xerox Welcome Center if the problem persists.
016-211 An error occurred due to insufficient memory. Check if memory is installed
correctly. If memory is installed correctly, and not being able to identify the cause
of the problem, contact the Xerox Welcome Center.
016-212 An error occurred due to insufficient memory. Check if memory is installed
correctly. If memory is installed correctly, and not being able to identify the cause
of the problem, contact the Xerox Welcome Center.
016-213 The software feature does not function properly, because the printer card is not
properly installed. Reinstall the printer card correctly.
016-214 The software feature does not function properly, because the fax card is not
properly installed. Reinstall the fax Card correctly.
016-450 The SMB host name already exists. Change the host name.
016-454 Unable to retrieve the IP address from DNS. Check the DNS configuration and
IP address retrieve setting.
016-455 Connection to the SNTP server was timed out. Check the network cable
connection and IP address of the SNTP server.
016-456 Received a message from the SNTP server saying that it was not synchronized
with the standard time source. Check the SNTP server settings.
016-502 An error occurred during writing data. Contact the Xerox Welcome Center.
016-503 Unable to resolve the name of the SMTP server when e-mail was transmitted.
Check if the SMTP server is set correctly using CentreWare Internet Services.
Also, check that the DNS server is set correctly.
016-504 Unable to resolve the name of the POP3 server when e-mail was transmitted.
Check if the POP3 server is set correctly using CentreWare Internet Services.
Also, check that the DNS server is set correctly.
016-505 Unable to log in to the POP3 server when transmitting e-mail. Check if the user
name and password used for the POP3 server are set correctly using
CentreWare Internet Services.
016-522 There was a LDAP server SSL authentication error. An SSL client certificate
could not be acquired. The LDAP server requires an SSL client certificate. Set
the SSL client certificate on the machine.
016-523 There was a LDAP server SSL authentication error. The server certificate data
was incorrect. The machine does not trust the LDAP server’s SSL certificate.
Register the root certificate of the LDAP server SSL certificate on the machine.
016-524 There was a LDAP server SSL authentication error. The server certificate is not
yet valid. Change to a valid LDAP server SSL certificate. The [Authentication
with SSL] setting in [LDAP Server/Directory Service can be set to [Disabled] to
avoid an error, but the connected LDAP server security is not guaranteed.
016-525 There was a LDAP server SSL authentication error. The server certificate has
expired. Change to a valid LDAP server SSL certificate. The [Authentication with
SSL] setting in [LDAP Server/Directory Service can be set to [Disabled] to avoid
an error, but the connected LDAP server security is not guaranteed.
016-526 There was a LDAP server SSL authentication error. The server name does not
match the certificate. Set the LDAP server address on the machine to match the
address on the LDAP server SSL certificate. The [Authentication with SSL]
setting in [LDAP Server/Directory Service can be set to [Disable] to avoid an
error, but the connected LDAP server security is not guaranteed.
016-527 There was a LDAP server SSL authentication error. There was an SSL
authentication internal error. This error was generated by the software. Contact
the Xerox Welcome Center.
016-533 There was a Kerberos server authentication protocol error. The machine and the
Kerberos server clocks have a time difference that exceeds the Kerberos server
clock skew value. Check that the machine and the Kerberos server clocks have
the correct time.
016-534 There was a Kerberos server authentication protocol error. The realm assigned
to the machine does not exist on the Kerberos server or the machine is not
connecting to the Kerberos server address. Check that the realm name and
Kerberos server address settings on the machine are correct. If connected with
Windows 2000 or Windows 2003 Server, make sure the realm name is in upper
case characters.
016-539 There was a Kerberos server authentication protocol error. This error was
generated by the software. Contact the Xerox Welcome Center.
016-701 An error occurred due to insufficient memory for the PCL decomposer. Lower
the resolution if possible.
016-702 Unable to process PCL print data due to insufficient print page buffer. Take one
of the following actions:
  • Set [Print Mode] to [High Speed].
  • Check if memory is installed correctly.
  • Set [Page Print Mode] to [On] in order to change the printing method, then try
    printing again.

For more information on Page Print Mode, refer to the print driver’s online help.

016-703 An e-mail specifying a non-registered or invalid mailbox number was received.
When sending a fax or Internet Fax:
  • Contact the Xerox Welcome Center.

When receiving e-mail, fax, or Internet Fax:

  • Register the mailbox with the specified number.
  • Send an e-mail to a valid mailbox.
  • Contact the Xerox Welcome Center if the problem persists.
016-704 The hard disk ran out of space, because the mailboxes are full. Delete
unnecessary documents from the mailboxes.
016-705 Unable to register the secure print document, mailbox document, or billing data
using the print driver, or unable to register the scanned document in the mailbox,
because the hard disk drive may not be installed properly on the machine, or
may be damanged. Contact the Xerox Welcome Center.
016-706 The hard disk ran out of space, because the number of users for secure printing
reached its maximum. Delete unnecessary documents or users registered for
the Secure Print feature.
016-707 Sample prints cannot be made due to the malfunction of the hard disk. Contact
the Xerox Welcome Center.
016-708 An annotation cannot be added due to insufficient hard disk space. Delete
unnecessary documents from the disk.
016-710 Delayed print job could not be excuted. Take one of the following actions:
  • Delete unnecessary data from the hard disk to increase free space.
  • Reset the settings of mailbox print and sample print.
  • Reduce the number of stored delayed print jobs to less than 100 jobs.
016-711 Refer to 016-985.
016-712 Refer to 003-751.
016-713 The input password does not match the mailbox password. Enter the correct password.
016-714 The specified mailbox does not exist. Create a new mailbox or specify an
existing mailbox.
016-716 The TIFF file could not be spooled as the size of the file exceeded the remaining space on disk. Increase the size of the PCL form area.
016-717 A [Transmission Report – Undelivered] or [Activity Report] was requested, but the the required transmission result information is not stored in memory, and the report was not generated. Take one of the following actions:
  • Partition memory intensive jobs (iFax) to limit the memory and the hard disk
    use.
  • Execute any pending scan and iFax jobs after other scan and iFax jobs are
    finished.
  • Request the report before 200 or more subsequent jobs have been executed.
016-718 Unable to process PCL print data due to insufficient memory. Take one of the
following actions:
  • Lower the resolution.
  • Use no multiple-up or 2 sided print feature, and try printing again.
016-719 Unable to process PCL print data due to insufficient print page buffer memory.
Increase the print page buffer.
016-720 PCL print data contained a command that could not be processed. Check the print data, and then try printing again.
016-721 An error occurred while printing a job. The Auto Tray Switching feature was
enabled when [Auto Paper Off] is selected for all paper trays on the [Paper Type
Priority] screen. When the Auto Tray Switching feature is enabled, select a
paper type other than [Auto Paper Off] on the [Paper Type Priority] screen.
016-722 The specified stapling position is not supported. Check the staple position, and try printing again.
016-723 The specified punch position is not supported. Check the punch position, and try printing again.
016-724 The combination of specified staple and punch options was imcompatible.
Specify punch and staple position along the same edge of the paper and try
printing again.
016-725 A scanned document saved in a mailbox could not be converted to fax data during transmission processing using the job flow sheet. Do not use the job flow
sheet. Instead scan the document, and send the fax directly.
016-726 The printer language cannot be automatically selected when the print mode is set to [Auto], including:
  • PostScript data was sent without the PostScript Kit installed. Install the PostScript Kit.
  • A PDF file is sent directly to the machine, but unable to process the job. The
    hard disk drive may not be installed properly on the machine or may be damaged. Contact the Xerox Welcome Center.
  • HP-GL/2 or PCL data is sent to the machine without the optional emulation kit. Install the emulation kit.
016-727 The result of a print request is a zero-page document that cannot be stored in a mailbox, and the job is canceled. Set the print option to print blank pages, and
reprint to confirm if the output is not blank. Add text if the output is blank, and try
printing again.
016-728 The TIFF file contains unsupported tags. Check the print data.
016-729 The TIFF file could not be printed, because the number of colors and resolution of the TIFF file exceeded the limit. Change the number of colors and resolution
of the TIFF file, and instruct it to print again.
016-731 Printing of the TIFF data was interrupted. Instruct it to print again.
016-732 The form specified in the emulation setting is not registered in the host
computer. Resend the form data.
016-733
  • Could not acquire the IP address from the text string after the @ character in an e-mail address. Enter the mail address correctly.
  • The DNS internet address after the @ character could not be resolved. Enter the DNS server address correctly.
016-734 Printing a simple recipient result report failed. Set the [E-mail Receive Protocol] on the sender’s end to [SMTP].
016-735 An attempt was made to print a job template while it was being updated. Wait a while, and then instruct it to print again.
016-736 Data is not stored in a forwarding address directory.
  • Check that there is space on the target disk.
  • Check the directory access permissions.
  • Delete any [.LCK] lock files in the target directory.
016-737 Data is not stored in a forwarding address directory. Delete any [.LCK] lock files in the target directory.
016-741 Unable to move onto the downloading mode.
016-742 Detected mismatching downloaded data product ID due to corrupt downloaded data. Try downloading again.
016-744 An error occurred to the data being downloaded. Check if the connection
between the external device and the machine is secured, and try executing the
operation again.
016-745 An XPJL error occurred while downloading. Try executing the job again. Contact the Xerox Welcome Center if the problem persists.
016-746 Received a PDF file that contains unsupported functions. Use a print driver to print the file.
016-747 An error occurred while processing the annotation image data due to insufficient memory. Take one of the following actions:
  • Increase the annotation image size.
  • Reduce the number of the images in [Repeat Image].

Contact the Xerox Welcome Center if the problem persists.

016-748 Unable to print due to insufficient hard disk space. Reduce the number of pages in print data, for instance by dividing the print data, or by printing one copy at a
time when making multiple copies.
016-749
  • The printer language received from a printer driver cannot be printed on the machine. Use the machine’s print driver. If the problem persists, contact the
    Xerox Welcome Center.
  • The printer language received in an iFax cannot be printed on the machine. Request that the sender sends the document using a printer language supported by the machine.
016-750 Printing banner sheets is canceled. Enter the System Settings mode on the touch screen, [Print Mode Settings] > [Other Settings], select [Banner Sheet]
and set [Start Sheet], also select [Banner Sheet Tray] and set [Tray 1].
016-751 An error occurred due to insufficient memory, when the PDF direct print function print mode is set to PostScript. Use the machine print driver, or increase the
PostScript memory.
016-753 The entered password does not match with that of the PDF file. Set the correct password on ContentsBridge.
016-755 An error occurred when processing a print job of a print-prohibited PDF file. Use Adobe Reader to release the print prohibition, and print the file.
016-756 The use of the service is restricted. Contact the Key Operator.
016-757 A wrong password was entered. Enter the correct password.
016-758 The account is not authorized for copying. Contact the Key Operator.
016-759 The maximum number of copies has been reached. Contact the Key Operator.
016-760 An error occurred during PostScript processing. Take one of the following
actions.
  • Set for optimized speed in the print driver.
  • Increase PostScript memory.
016-761 An error occurred during image processing. Set [Image Options] > [Image Quality] > [High Speed] on the print driver, and print again. If this does not rectify printing, set [Detailed Settings] > [Other Settings] > [Print Page Mode] on the
print driver, and try again.
016-762 The specified print language is not supported on the machine. Specify the print language in [Print Mode] under [Port Settings].
016-764 Unable to connect to the SMTP server. Contact the System Administrator.
016-765 Unable to send e-mail due to insufficient hard disk space on the SMTP server. Contact the System Administrator.
016-766 An error occurred on the SMTP server. Contact the System Administrator.
016-767 Unable to send e-mail due to the wrong e-mail address. Verify the e-mail
address, and try sending the e-mail again.
016-768 Unable to connect to the SMTP server due to the incorrect e-mail address of the machine. Check the e-mail address of the machine.
016-769 The SMTP server does not support delivery confirmation (DSN). Send e-mail without setting confirmation.
016-770 The direct fax function is prohibited. Check with the System Administrator whether the function is enabled. If enabled, contact the Xerox Welcome Center.
016-771 Unable to retrieve the scan data repository address. Confirm the DNS
connection. Alternatively, set the scan data repository domain name to the DNS.
016-772 Unable to retrieve the scan data repository address. Specify the correct DNS address. Alternatively, set scan data repository address to the IP address.
016-773 The IP address of the machine is not set correctly. Check the DHCP
environment. Alternatively, manually specify an IP address of the machine.
016-774 Unable to process compression conversion due to insufficient hard disk space. Delete unnecessary data from the disk.
016-775 Unable to process the image conversion due to insufficient hard disk space. Delete unnecessary data from the disk.
016-776 An error occurred during image conversion processing. Check the data in
CentreWare Internet Services.
016-777 An error occurred on the hard disk during image processing, probably due to a hard disk malfunction. For details on replacing the hard disk, contact the Xerox
Welcome Center.
016-778 Conversion of the scanned image was discontinued due to insufficient disk space. Delete unnecessary data from the disk.
016-779 An error occurred during conversion processing of the scan image. Instruct scanning again.
016-780 An error occurred on the disk during conversion processing of the scanned image, probably due to a disk malfunction. For details on replacing the hard
disk, contact the Xerox Welcome Center.
016-781 Unable to connect to the server during file forwarding by CentreWare Scan Services. Ask the System Administrator to check the network and server.
016-782 Unable to connect to the server for CentreWare Scan Services. Verify that the login user name, password and other information that are entered.
016-783 Unable to find the specified server path during file forwarding by CentreWare Scan Services. Check the path name of the server currently set to the job
template.
016-784 A write to server error occurred during file forwarding by CentreWare Scan Services. Confirm that there is sufficient space in the directory on the server,
and that access rights are present.
016-785 The file could not be sent by CentreWare Scan Services due to insufficient space on the server. Delete unnecessary data from the server.
016-786 The scanned data could not be written due to insufficient space on the hard disk. Delete unnecessary data, or initialize the hard disk if the saved data are not
needed anymore.
016-787 The server IP address set to the job template is incorrect. Specify the correct job template.
016-788 Failed to retrieve the file from the web browser. Take one of the following
actions, and then try retrieving again.
  • Refresh the browser page.
  • Restart the browser.
  • Switch the machine off then back on.
016-789 The mail processing was interrupted due to insufficient hard disk space. Lower the image resolution or reduction/enlargement ratio, or divide the document into
smaller segments to send.
016-791 The access to the specified destination or job template server failed when using Scan To FTP/SMB or CentreWare Scan Services. Check if you are authorized to
access the specified destination or server.
016-792 The specified job history could not be retrieved when printing a job history report. The specified job history is not available.
016-793 The hard disk has run out of space. Delete unnecessary data or initialize the hard disk if the saved data are not needed anymore.
016-794 The media was incorrectly inserted. Reinsert the media correctly.
016-795
016-796
016-797
A read error occurred when reading data on the media. Check the contents stored on the media using a computer.
016-798 The print could not be processed. The hard disk drive or memory may not be installed properly on the machine, or may be damaged. Contact the Xerox
Welcome Center.
016-799 The print data contains invalid parameters. Check the print data and print
options and try printing again.
016-982 The hard disk has run out of space. Delete unnecessary data from the hard disk or documents in mailboxes.
016-985 The e-mail size exceeds the maximum size. Try one of the following procedures, and resend the e-mail.
  • Reduce the number of pages in the document.
  • Lower the resolution in [Scan Resolution].
  • Reduce the document size using [Reduce/Enlarge].
  • Increase the maximum value in [Maximum E-mail Size] using the Key Operator access.
018-505 An authentication error occurred due to an incorrect user name and/or
password. Check that the user name and password are correct.
018-701 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 1 (operations error)
during the address book query. Check that the [LDAP Server/Directory Service]
settings in [Remote Authentication Server/Directory Service] are correct, and
check if the problem occurred on the server side.
018-702 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 2 (protocol error)
during the address book query. Review the LDAP server settings and repeat the
same operation.
018-703 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 3 (time limit exceeded)
during the address book query. Review the search conditions and search root
entry, then repeat the same operation. Contact the network administrator if the
problem persists.
018-704 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 4 (size limit exceeded)
during the address book query. Review the search conditions and search root
entry, then repeat the same operation. Contact the network administrator if the
problem persists.
018-705 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 5 (compare false)
during the address book query. The compare operation returned false. Check
the LDAP server status.
018-706 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 6 (compare true)
during the address book query. The compare operation returned true, indicating
there is no problem.
018-707 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 7 (authentication method not supported) during the address book query. Change the authentication method and review the authentication settings.
018-708 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 8 (strong authentication required) during the address book query. Check that there are no errors in the authentication settings, and strengthen subsequent authentication.
018-710 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 10 (referral) during the
address book query. There is nothing registered in the specified search range. Check the authentication settings status.
018-711 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 11 (admin limit exceeded) during the address book query. Check the server operating status.
018-712 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 12 (unavailable critical
extension) during the address book query. Check the server operating status.
018-713 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 13 (confidentiality required) during the address book query. Check the server operating status.
018-714 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 14 (SASL bind in progress) during the address book query. Wait a while, then repeat the same operation. Contact the network administrator if the problem persists.
018-716 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 16 (no such attribute)
during the address book query. The specified attribute does not exist. Check the LDAP server status.
018-717 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 17 (undefined attribute
type) during the address book query. The attribute type specified is invalid. Check the LDAP server status.
018-718 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 18 (inappropriate
matching) during the address book query. Filter type not supported for the specified attribute. Check the LDAP server status.
018-719 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 19 (constraint violation) during the address book query. An attribute value specified violates some constraint. Check the LDAP server status.
018-720 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 20 (attribute or value exists) during the address book query. An attribute type or value already exists. Check the LDAP server status.
018-721 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 21 (invalid attribute syntax) during the address book query. An invalid attribute syntax was specified. Check the LDAP server status.
018-732 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 32 (no such object) during the address book query. The specified e-mail address does not exist in the directory. Review the input e-mail address and check the e-mail address is registered on the LDAP server.
018-733 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 33 (alias problem) during the address book query. The alias (name) in the directory points to a nonexistent entry. Check the LDAP server status.
018-734 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 34 (invalid DN syntax)
during the address book query. An invalid DN syntax was specified. Check the user name and password. Check the LDAP server authentication settings and other status.
018-735 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 35 (is leaf) during the
address book query. The object specified is a leaf node. Check the LDAP server status.
018-736 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 36 (alias dereferencing
problem) during the address book query. The error occurred while dereferencing an alias. Check the LDAP server status.
018-748 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 48 (inappropriate authentication) during the address book query. Inappropriate authentication was specified. Check the LDAP server authentication settings.
018-749 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 49 (invalid credentials)
during the address book query. Invalid credentials (user name or password) was specified. Check the user name and password. Check the LDAP server authentication settings.
018-750 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 50 (insufficient access
rights) during the address book query. User has insufficient access to perform the operation. Check the LDAP server access rights.
018-751 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 51 (busy) during the address book query. The server is too busy. Wait a while, then repeat the same operation. Contact the network administrator if the problem persists.
018-752 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 52 (unavailable) during the address book query. The server is unavailable. Wait a while, then repeat the same operation. Contact the network administrator if the problem persists.
018-753 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 53 (unwilling to perform) during the address book query. The server is unwilling to perform the operation. Wait a while, then repeat the same operation. Contact the network administrator if the problem persists.
018-754 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 54 (loop detect) during the address book query. A loop was detected (service-related problem). Check the LDAP server service operating status.
018-764 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 64 (naming violation)
during the address book query. A naming violation occurred (update-related problem). Check the LDAP server status.
018-765 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 65 (object class violation) during the address book query. An object class violation occurred (update-related problem). Check the LDAP server status.
018-766 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 66 (not allowed on nonleaf) during the address book query. The operation is not allowed on a nonleaf object (update-related problem). Check the LDAP server status.
018-767 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 67 (not allowed on RDN) during the address book query. The operation is not allowed on an RDN (update-related problem). Check the LDAP server status.
018-768 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 68 (entry already exists) during the address book query. The entry already exists (update-related problem). Check the LDAP server status.
018-769 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 69 (object class mods
prohibited) during the address book query. Object class modifications are prohibited (update-related problem). Check the LDAP server status.
018-770 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 70 (search result too large) during the address book query. Review the search conditions and search root entry, then repeat the same operation. Contact the network administrator if the problem persists.
018-771 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 71 (affects multiple DSAs) during the address book query. Check the LDAP server status.
018-780 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 80 (unknown error) during the address book query. Check the LDAP server status.
018-781 An LDAP server protocol error occurred in the address book operation. Could not connect to the server. Use the following methods:
  • Check the network cables are connected.
  • Check the target server’s operating status.
  • Check that the server name in the [LDAP Server/Directory Service] settings in
    [Remote Authentication Server/Directory Service] are correct.
018-782 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 82 (program error or
SASL authentication error) during the address book query. Check the LDAP
server status.
018-783 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 83 (send message encoding error) during the address book query. Check the LDAP server status.
018-784 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 84 (receive message
decoding error) during the address book query. Check the LDAP server status.
018-785 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 85 (search result timeout) during the address book query. Review the search conditions and search root entry, then repeat the same operation. Contact the network administrator if the problem persists.
018-786 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 86 (unknown authentication method specified) during the address book query. Check the LDAP server status.
018-787 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 87 (invalid search filter
supplied) during the address book query. Review the search conditions. Contact the network administrator if the problem persists.
018-788 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 88 (operation canceled) during the address book query. Check the LDAP server status.
018-789 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 89 (parameter error) during the address book query. Check the LDAP server status.
018-790 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 90 (memory allocation error) during the address book query. Check the LDAP server status.
018-791 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 91 (server connection error) during the address book query. Check the LDAP server status.
018-792 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 92 (unsupported function) during the address book query. Check the LDAP server status.
018-793 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 93 (result not returned)
during the address book query. Check the LDAP server status.
018-794 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 94 (result no longer available) during the address book query. Check the LDAP server status.
018-795 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 95 (result still available) during the address book query. Check the LDAP server status.
018-796 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 96 (client loop detected) during the address book query. Check the LDAP server status.
018-797 An LDAP server protocol error occurred in the address book operation. The server returned the RFC2251 specification protocol error 97 (maximum number of reference hops exceeded) during the address book query. Check the LDAP server status.
024-742 The number of print pages, using print options, in a booklet creation job exceeds the number of maximum pages. Divide the job into manageable jobs or cancel book creation.
024-746 The selected option (i.e., paper size, document tray, output tray, or double-sided printing) is incompatible with the specified paper quality. Check the print data.
024-747 An invalid print parameter combination was set. Check the print data. For
example, a custom size was specified, and [Paper Supply] was set to [Auto]. In this case, select the bypass tray.
024-985 An error occurred in the bypass tray. Check the document size, orientation, and paper type, then try executing the same operation again.
026-700 A protocol which is not supported on the machine was received from the LDAP server during an address book query. Try executing the same operation again. Contact the Xerox Welcome Center if the problem persists.
026-701 The number of address book requests exceeded the handling capacity of the machine. Wait a while, and perform the same operation again. If there is only one address book request, the problem may be in the machine software. Contact the Xerox Welcome Center.
026-702 The number of transactions from the LDAP server exceeded the handling
capacity of the machine. Wait a while and perform the same operation. Contact the Xerox Welcome Center if the problem persists.
027-452 The specified IP address already exists. Change the IP address.
027-500 Unable to resolve the name of the SMTP server when reply e-mail was
transmitted. Check from CentreWare Internet Services to see if the SMTP server is set correctly.
027-501 Unable to resolve the name of the POP3 server when using the POP3 protocol. Check from CentreWare Internet Services to see if the POP3 server is set
correctly.
027-502 Unable to login to the POP3 server when using the POP3 protocol. Check from CentreWare Internet Services to see if the user name and password used for
the POP3 server are set correctly.
027-547 An SMB protocol error occurred. Prohibited characters were detected in thespecified domain name. Check the domain name, and that the correct domain
name is set on the machine. Check the domain by:
  1. Select [System Settings] > [Network Settings] > [Remote Authentication
    Server/Directory Service] > [SMB Server Settings] in System Administrator
    mode.
  2. Select the corresponding SMB server and check the domain name.
027-548 An SMB protocol error occurred. Prohibited characters were detected in the specified user name. Check the user name settings.
027-549 An SMB protocol error occurred. Perform the same operation again. Contact the Xerox Welcome Center if the problem persists.
027-564 An SMB protocol error occurred. The SMB server cannot be found. Check that the authentication server and the machine can communicate across the network. For example, check the following:
  • Check the network cable connections.
  • Check the TCP/IP settings.
  • Check the port settings; port 137 (UDP), port 138 (UDP), port 139 (TCP).
027-565 An SMB protocol error occurred. Perform the same operation again. Contact the Xerox Welcome Center if the problem persists.
027-566 An SMB protocol error occurred. SMB (TCP/IP) is not activated. Using
CentreWare Internet Services, open the [Port Status] window in the [Properties] tab, and check that TCP/IP for SMB is enabled.
027-572
027-573
027-574
027-576
027-578
An SMB protocol error occurred. Perform the same operation again. Contact the Xerox Welcome Center if the problem persists.
027-584 An SMB protocol error occurred. The SMB server is operating in share security mode. The SMB server is probably set on an Windows 95, Windows 98, or
Windows ME OS. Set the SMB server on an OS other than Windows 95, Windows 98, or Windows ME.
027-585 An SMB protocol error occurred. Login prohibited time interval. Check allowed login time with the System Administrator.
027-586 An SMB protocol error occurred. The password valid interval has expired.
Obtain a valid password from the System Administrator.
027-587 An SMB protocol error occurred. The password change interval has expired. Login on Windows, and change the password. Ask the System Administrator to
change the change interval settings to avoid being prompted the next time you login.
027-588 An SMB protocol error occurred. The user account is disabled. Ask the System Administrator to enable the user.
027-589 An SMB protocol error occurred. The user account is locked out. Ask the
System Administrator to release the lockout.
027-590 An SMB protocol error occurred. The user valid interval has expired. Obtain a valid user account from the System Administrator, or ask the System Administrator to extend the account interval.
027-591 An SMB protocol error occurred. The user account is restricted. The blank password is invalid. Set the user account password.
027-593
027-599
An SMB protocol error occurred. Perform the same operation again. Contact the Xerox Welcome Center if the problem persists.
027-706 There was no S/MIME certificate tied to the e-mail address when sending e-mail. Import an S/MIME certificate for the e-mail address into the machine.
027-707 The S/MIME certificate tied the e-mail address when sending e-mail has
expired. Obtain a new S/MIME certificate, and import into the machine.
027-708 The S/MIME certificate tied the e-mail address when sending e-mail is
untrusted. Import a trusted S/MIME certificate into the machine
027-709 The S/MIME certificate tied the e-mail address when sending e-mail has been revoked. Import a new S/MIME certificate into the machine.
027-710 The S/MIME certificate to receive e-mail was not present. Contact the sender, and ask them to send e-mail with an S/MIME certificate.
027-711 The sender’s S/MIME certificate was not retrieved from the received e-mail. Import the sender’s S/MIME certificate into the machine, or attach an S/MIME
certificate to the sender’s S/MIME signature e-mail.
027-712 The received e-mail S/MIME certificate has expired or is untrusted. Contact the sender, and ask them to send e-mail with a valid certificate.
027-713 The received e-mail was rejected, because it had been altered, possibly the transmission route had been falsified. Contact the sender to notify them about
the possibility of falsification, and request them to resend the e-mail.
027-714 The received e-mail was rejected, because the “From” field differs from the S/MIME signature e-mail address. Contact the sender, tell them about the possibility of impersonation, and ask them to resend the e-mail.
027-715 The received e-mail S/MIME certificate is not registered on the machine or is not supported on the machine. Import the sender’s S/MIME certificate into the machine, or if already registered, enable the certificate so that it can be used on the machine.
027-716 The received e-mail was rejected, because the S/MIME certificate was
untrusted. Contact the sender, and ask them to send e-mail with a trusted certificate.
027-737 An error occurred during reading of data from the job template server. Check the access rights of the directory in which the job template is stored.
027-739 Unable to find the specified job template server. Check the path name to the job template server.
027-740 Unable to log in to the job template server. Verify that the correct log-in user name, password and other information are entered.
027-741 Unable to connect to the job template server. Ask the network administrator to check the network or server.
027-742 The job template could not be stored to memory due to insufficient disk space. Delete unnecessary data from the disk.
027-743 The settings on the job template server are incorrect. Check the settings of the job template server.
027-744 There is a problem in the domain name of the job template server. Make sure that the DNS server connection and the domain name are registered to the DNS
server.
027-745 The address of the DNS server is not registered on the machine. Register the address of the DNS server on the machine, or set the address of the job template server as an IP address.
027-746 The protocol setting of the job template server is not correct. Set up the correct port.
027-750 Fax forwarding, printing, or Internet Fax forwarding was attempted for a
scanned document. Fax forwarding, printing, and Internet Fax forwarding cannot be performed for scanned documents.
027-751 An error occurred while processing a job flow sheet. Check the job flow sheet.
027-752 The job flow has a parameter that requires user input that was not entered. Perform one of the following:
  • Do not tie the job flow with required user input to a mailbox.
  • Set the default values for the job flow required user input parameters.
027-753 The required port was not open to the job attempted by a job flow sheet. Contact the Key Operator.
027-754 The settings for [DocuWorks Signature] or [PDF Signature] on the job flow are incorrect. Check the DocuWorks and PDF signatures for both the system data
settings (machine’s current settings) and the executed job flow settings. If these settings are not the same, change either of them.
027-796 E-mail without an attachment was discarded, because the machine is set to print only the attached document of e-mail. To print body text and the header of
e-mail in addition to its attachments, change settings in [Properties] on CentreWare Internet Services.
027-797 The output destination is not correct. Specify the correct destination, and resend the e-mail.
033-363 An error occurred when using the fax. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
033-710 The document for polling has been deleted. Store the original document again.
033-712 The processing could not continue due to insufficient system memory. Delete unnecessary data.
033-713 An error occurred when using the fax. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
033-716 The mailbox specified by the remote machine does not exist. Register the
mailbox on the machine.
033-717 The mailbox password specified by the remote machine is incorrect, or the password-receive password is incorrect. Notify the correct password to the sender.
033-718 There are no fax documents or no documents for polling in the mailbox specified by the remote machine. If required, store the fax document or document for
polling in the mailbox.
033-719 The fax job was canceled when the supply was turned off and on. Send the document again.
033-721 An error occurred when using the fax. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
033-722 The scan job was canceled due to power supply problem, or because the
document exceeds the maximum number of pages that can be stored. Check the power supply, or set documents that are smaller than the maximum number of pages.
033-724 Unable to receive the image data, because the data size that can be received per a fax transmission exceeds its upper limit. Request the sender to devide the
document into smaller segments to send, or lower the resolution. If the problem persists, check if memory is installed correctly. If memory is installed correctly, and not being able to identify the cause of the problem, contact the Xerox Welcome Center.
033-725 The hard disk is full. Delete unnecessary data on the hard disk to increase the available hard disk space.
033-726 The received document was printed single sided, because the 2-sided printing is not available for a mixed size document. No user action is required.
033-727 The received page data size is too large to rotate automatically to shift the document orientation on the page. The pages are printed without rotation. No user action is required.
033-728 The Auto Print formatting of the received fax document was interrupted by a manual print operation. No user action is required. The machine will automatically resume the Auto Print job after manual printing is done.
033-731 The Auto Print processing for the received fax document was interrupted by a manual print operation. No user action is required.
033-733 An error occurred when using the fax. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
033-734 The fax print was suspended, because a job report was generated while
preparing the fax print job. No user action is required.
033-735 An error occurred using the fax. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
033-736 The transmission was canceled, because the transmit data size exceeded its upper limit. No user action is required.
033-737 An error occurred using the fax. Perform the same operation again.
033-738 Abnormal JBIG image data was received. No user action is required.
033-740 The print job for the received fax document was canceled. No user action is required.
033-741 An error occurred when using the fax. Perform the same operation again.
033-742 Contact the Xerox Welcome Center if the problem persists.
033-743
033-744
033-745
033-746
An error occurred when using the fax. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
033-747 The job was suspended. No user action is required.
033-749 The machine rectified a memory problem automatically for printout. No user action is required.
033-750 An error occurred when using the fax. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
033-751 An attempt was made to output the maintenance report unsucessfully, while the machine is in Sleep Mode when any printing is prohibited. The report print job
will be resumed as soon as the print prohibited Sleep Mode interval ends.
033-755 Unable to print the fax document due to the fax malfunction. Take one of the following actions:
  • Turn the power off and on.
  • Make sure that the cable connecting the machine and the Fax Card is plugged in securely.
  • Check the touch screen message, or print out the error job history report to find out the fault code. Contact the Xerox Welcome Center if the problem persists.
034-211
034-212
An error occurred in the fax controller. Contact the Xerox Welcome Center.
034-500 An incorrect telephone/fax number was dialed. Check the number, then perform the same operation again.
034-501 The telephone cable may not be connected securely. Check that the telephone cable is connected correctly, and resend the document. Refer to Telephone
socket in the Product Overview chapter on page 34.
034-505 An error occurred using the fax. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
034-506 The remote copy function (printing multiple copies of a received document) is not supported on the destination machine. Check if the destination machine
supports the remote copy function.
034-507 Communication failed, because the password you specified does not match with the ID number of the destination machine. Make sure that the password and
telephone number are correct. The destination machine may be set not to send
its own ID number. This code is also displayed when a polling request is rejected.
034-508
034-509
034-510
An error occurred when using the fax. If sending a fax, check the fax setting, fax number, and other settings, then perform the same operation again. Contact the Xerox Welcome Center if the problem persists.
034-511 A document for relay broadcasting cannot be transmitted. Check that the relay station is correctly registered in the specified speed dial code. Also, check the
contents of the address number registered at the relay station.
034-513 Received an invalid command. This is a Xerox remote maintenance system
operational error. No user action is required.
034-514 Received an unsupported request. This is a Xerox remote maintenance system operaional error. No user action is required.
034-512 An endless loop was detected in the remote relay broadcasting. Check that the relay station is correctly registered in a speed dial number, and check the speed
dial number points to the relay station.
034-515 There is a problem on the remote machine. Check the remote machine status.
034-519 The number of destinations exceeded the maximum number during broadcast transmission. Wait for the pending jobs to decrease or reduce the number of
destinations, then repeat the same operation.
034-520 The number of jobs to be received exceeds the maximum number. Wait for the pending jobs to reduce and then repeat the operation.
034-521 An internal error occurred. Turn the power off and on. Contact the Xerox
Welcome Center if the problem persists.
034-522 There is no phone line available for manual send communication. Wait until current transmissions to end, then perform the same operation again.
034-523 The fax service has been disabled, and jobs cannot be received. Wait a while, then perform the same operation again.
034-527 A dial control error occurred. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
034-528 Unable to perform manual send during dialing. Try executing the same
operation again when not dialing.
034-529 The received document cannot be printed on the paper loaded on the machine. Try one of the following:
  • Check that the correct paper size is loaded in the machine.
  • Check that the tray is correctly placed in the machine.
034-530 Operation timed out. Perform the operation within the specified time frame.
034-550 An error occurred while processing to write onto the FaxCard-ROM. Contact the Xerox Welcome Center.
034-700 The G3 DP (Dial Pulse) connection timed out. Turn the power off and on.
Contact the Xerox Welcome Center if the problem persists.
034-701 The software needs to be reset. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
034-702 Communication failed due to an incorrect telephone or fax number. Check the number, and perform the same operation again. If a speed dial button was used,
check the correct number is registered appropriately.
034-728 An invalid number was specified. Check the destination number, and perform the same operation again. Contact the Xerox Welcome Center if the problem
persists.
034-730
034-731
Refer to 034-508.
034-734 An internal error occurred. Turn the power off and on. Contact the Xerox
Welcome Center if the problem persists.
034-796 An invalid data was found in the dialing data. Dial the number again, then
perform the same operation.
034-797 An communication parameter error occurred. Turn the power off and on.
Contact the Xerox Welcome Center if the problem persists.
034-798 A data parameter error occurred. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
034-799 Dialing data is not registered, even though the auto dial feature was specified. Turn the power off and on. Contact the Xerox Welcome Center if the problem
persists.
035-700 An error occurred using the fax. Perform the same operation again. Contact the Xerox Welcome Center if the problem persists.
035-701 Unable to communicate due to an incorrect phone number. Check the phone number, and perform the same operation again. If DP (Dial Pulse) is used for G3, check that “” and “#” are not included in the phone number.
035-702
035-703
The other party cancelled the transmission. Ask the other party to check their machine status, and resend the document if necessary.
035-704 The specified feature (such as polling) is not supported by the remote machine. Contact the other party to check the supported functions.
035-705
035-706
The remote machine may have encountered a problem. Contact the other party and resend the document if necessary.
035-707 No password was specified or an invalid password was specified. This only notifies that the machine received such document, so that no user action is required.
035-708
035-709
035-710
035-712
035-713
The remote machine may have encountered a problem. Contact the other party and resend the document if necessary.
035-714 Refer to 035-702.
035-715 Refer to 035-507.
035-716
035-717
035-718
035-719
A communication error occurred. Contact the other party, and resend the document if necessary.
035-720 The destination machine cannot receive the document that you sent. Ask the other party to check the following:
  • Their machine has paper in the tray
  • Their machine has no paper jam
  • Their machine has enough memory
  • Their machine supports G3 reception.

When specifying features such as relay broadcasting or a remote mailbox, ask the other party if their machine supports these features, and if the password is correct.

035-721
035-722
A communication error occurred. Ask the other party to resend the document if necessary.
035-723
035-724
A communication error occurred. If sending, check the telephone/fax number, Check if the features you specified are supported on the destination machine, then perform the same operation again. If receiving, ask the other party to
resend the document if necessary.
035-725 Refer to 034-511.
035-726 A communication error occurred. If sending, check the telephone/fax number, Check if the features you specified are supported on the destination machine,
then perform the same operation again. If receiving, ask the other party to resend the document if necessary.
035-727
035-728
035-729
A communication error occurred. Ask the other party to resend the document if necessary.
035-730
035-731
035-732
035-733
035-734
035-735
035-736
035-737
035-738
035-739
035-740
035-741
035-742
A communication error occurred. If sending, check the telephone/fax number, Check if the features you specified are supported on the destination machine, then perform the same operation again. If receiving, ask the other party to resend the document if necessary.
035-743
035-744
035-745
Communication failed due to an incorrect telephone/fax number, or because the specified function is not available on the remote machine. Check the telephone/fax number, functions supported on the remote machine, and other settings and repeat the same operation.
035-746 The fax network does not respond. Check the following, and send the document again.
  • Is the telephone line correctly connected to the machine?
  • The other party may not be connected to the fax network, or there may be some problem with the network.

When you are connected to a fax network that requires an access code, enter two pauses after the access code, and then dial the telephone number.

035-747
035-748
Transmission was stopped, because the button was pressed while dialing or sending. No user action is required.
035-749 The other party’s telephone number was redialed the set number of times but the remote machine did not answer. Ask the other party to check the telephone
line and connection to the machine.
035-750 Transmission was stopped because the button was pressed while dialing or sending. Turn the machine on again and resend the document. Contact the Xerox Welcome Center if the problem persists.
035-751
035-752
Transmission was stopped, because the button was pressed while dialing or sending. No user action is required.
035-762 Refer to 034-508.
036-500
036-542
036-700
to
036-777
An error occurred when using the fax. If sending a fax, check the contents, fax to number, and other settings, then perform the same operation again. Contact the Xerox Welcome Center if the problem persists.
036-778
036-779
Communication was interrupted on the destination machine side. Ask the other party to resend the document if necessary.
036-780
036-781
036-782
036-783
036-784
036-785
An error occurred when using the fax. If sending a fax, check the contents, fax number, and other settings, then perform the same operation again. Contact the Xerox Welcome Center if the problem persists.
036-786
036-787
Refer to 034-507.
036-788
036-789
A transmission when using polling was specified, but there is no document for polling on the destination machine. Contact the other party to confirm, and perform the same operation if necessary.
036-790
036-791
Communication failed due to invalid request. Check the procedure in the User Guide and perform the operation again.
036-792
036-793
Refer to 034-508.
036-795 The remote copy function (printing multiple copies of a received document) is not supported on the destination machine. Check if the remote copy function
exists on the destination machine.
036-796 The transmission mode switched to normal operating mode, because the
remote copy function (printing multiple copies of a received document) was not supported on the destination machine. No user action is required.
036-797
036-798
036-799
Refer to 034-508.
047-211 A hardware problem occurred in the paper output assembly. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists..
047-214 An error occurred in the Duplex Module. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
047-216 An error occurred in the finisher. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
062-210 The document feeder malfunctioned. Contact the Xerox Welcome Center.
062-211 An error occurred in the document feeder. Contact the Xerox Welcome Center.
062-220 Refer to 062-210.
062-277 A communication error occurred between scanning and feeding components of the machine. Contact the Xerox Welcome Center.
062-278 An error occurred in the document feeder. Contact the Xerox Welcome Center.
062-790 The scanned document is copy-prohibited. Refer to Illegal Copies in the Before Using the Machine chapter on page 29, and verify the types of documents that
can be copied.
071-210
071-212
An error occurred when using Tray 1. Turn the machine off and on. Contact the Xerox Welcome Center if the problem persists.
072-210
072-212
An error occurred when using Tray 2. Turn the machine off and on. Contact the Xerox Welcome Center if the problem persists.
073-210
073-212
An error occurred when using Tray 3. Turn the machine off and on. Contact the Xerox Welcome Center if the problem persists.
077-215 An error occurred when using Two Tray Module. Turn the machine off and on. Contact the Xerox Welcome Center if the problem persists.
078-210 An error occurred when using High Capacity Feeder Tray 1. Turn the machine off and on. Contact the Xerox Welcome Center if the problem persists.
078-211 An error occurred when using High Capacity Feeder Tray 2. Turn the machine off and on. Contact the Xerox Welcome Center if the problem persists.
081-799 The fax job was cancelled due to the fax transmission limit when sending the job using e-mail. Try executing the job again.
116-220 Download failed to start after switching to download mode. Contact the Xerox Welcome Center.
116-701 Unable to print double-sided due to insufficient memory. Check if memory is installed correctly. If memory is installed correctly, and not being able to identify the cause of the problem, contact the Xerox Welcome Center.
116-702 Printing was performed using a substitute font. Check the print data.
116-703 An error occurred during PostScript processing. Either confirm the print data, or open spool settings on the details tab in the print driver to disable bi-directional
communication.
116-713 The job was printed out in parts because the hard disk ran out of space. Delete unnecessary data.
116-714 A HP-GL/2 command error occurred. Check the print data.
116-720 An error occurred during printing due to insufficient memory. Close unused ports or delete unnecessary data.
116-740 A numerical value operation error occurred, because the print data contains a value that exceeds the limit of the printer. Check the print data.
116-749 The print job was stopped, because the specified font was not found. Install the font or enable font replacement in the print driver.
116-752 There was a warning in the PDF print job ticket description. Repeat the same procedure. Contact the Xerox Welcome Center if the problem persists.
116-771
116-772
116-773
116-774
116-775
116-776
116-777
116-778
The parameter values were corrected, because the machine encountered a problem when printing the data. If the received image is incomplete or damaged, ask the other party to check the image or to resend the data. When Internet Fax forwarding is enabled, check with the recipient if they received the image intact.
116-780 There is a problem with the document attached to the received e-mail. Check the attached document.
116-790
  1. If the operator stops stapling while printing a confidential fax or confidential iFax document, the first copy is printed without staples. Staple the first copy
    manually, or otherwise do not stop stapling while printing.
  2. If the operator stops stapling in all other cases: all copies are printed without staples. Check that the stapling position is correctly specified, and perform the same operation again.
123-400 The machine has detected a software-related problem. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
124-701 Due to a malfunction in the specified tray (side tray), the output destination was changed to the center output tray. Contact the Xerox Welcome Center. A
different paper tray can still be used.
124-702 Due to a malfunction in the specified tray (finisher tray), the output destination was changed to the center output tray. Contact the Xerox Welcome Center. A
different paper tray can still be used.
133-210
133-211
133-212
133-213
133-214
133-215
133-216
133-217
133-218
133-219
133-220
133-221
133-222
133-223
133-224
An error occurred when using the fax. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
133-226 A country code not compatible with the machine that was specified. Contact the Xerox Welcome Center.
133-280
133-281
133-282
133-283
An error occurred when using the fax. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.
134-210
134-211
An error occurred when using the fax. Turn the power off and on. Contact the Xerox Welcome Center if the problem persists.

Our Services